Rationale for granulometric medium characteristics under vibration processing of parts with small grooves and holes

Introduction. The design technique for a highly efficient technological process of vibration finishing of parts with small grooves and holes is presented. The decision is based on the selection of the granulometric characteristics of the processing environments. The cross-sectional shape and geometrical dimensions of burrs on typical parts of radio electronic equipment (REE) are analyzed. A generalized burr model has been developed. Methodological principles for the selection of particle size characteristics of operating environments are determined.

Materials and Methods. The new classification and coding according to the constructive and technological principles of REE components will provide reasonable selection of the equipment, environments and modes when designing their finishing process.

Results. A technique has been developed for selecting the granulometric characteristics of operating environments with the account of the major technological problems. Based on the design and technological features of the REE components, the dependences are proposed for determining the size and shape of the processing granules. The acceptance criteria for evaluating the results of vibration processing are determined. It is noted that one of the major tasks in the vibration processing of parts with small grooves and holes is to provide such in-process time at which burrs are removed, and the roughness and other surface parameters meet the technical requirements. In this case, the accuracy of the linear dimensions of the processed surfaces should be considered an indicator of quality. Quantitatively, this criterion is assessed on a specific index whose calculation considers the largest actual size before vibration processing, the burr height, the smallest allowable size after processing, and the tolerance established by the technical requirements. The process efficiency criterion is defined as the ratio of the machinability index to the processing time of a batch of parts or the cycle time per part. The proposed criterion enables to compare treatment processes under validating the solution to technological problems.

Discussion and Conclusions. The study results enable to confirm that vibration processing in the organic environment contributes to the effective removal of burrs and edge smoothing of small-sized parts of electronic equipment with small grooves and holes.

1. Kolganova, E. N. Investigation of deburring process at vibro-abrasive treatment of parts having small grooves and holes / E. N. Kolganova, V. M. Goncharov, A. V. Fedorov // Materials today. — 2019. — Vol. 19 (5). — P. 23682373.

2. Тамаркин, М. А. Анализ современного состояния финишных методов обработки в среде свободных абразивов деталей, имеющих малые пазы и отверстия / М. А. Тамаркин, Е. В. Смоленцев, Е. Н. Колганова // Вестник Воронежского государственного технического университета. — 2019. — Т. 15, № 1. — С. 122-129.

3. Antonova, N. M. Adhesion of a vibration mechanochemical solid-lubricant MoS(2) coating / N. M. Antonova, V. S. Shorkin, S. N. Romashin [et al.] // Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques. — 2019. — Vol. 13 (5). — P. 848-854. DOI: 10.1134/S1027451019040025

4. Ivanov, V. V. The research of technological characteristic of the vibrowave mechanical and chemical oxide coating formation / V. V. Ivanov, A. P. Babichev, N. P. Pogorelov // 13th International scientific-technical conference on dynamic of technical systems (DTS) : MATEC Web of Conferences. — 2017. — Vol. 132. — P. 01004. DOI: 10.1051/matecconf/201713201004

5. Ivanov, V. V. Qualitative Characteristics of MoS2 Solid-Lubricant Coating Formed by Vibro-Wave Impact of Free-Moving Indenters / V. V. Ivanov, S. I. Popov, A. V. Kirichek // Key Engineering Materials. — 2017. — Vol. 736. — P. 18-22.

6. Lebedev, V. А. Increase of efficiency of finishing-cleaning and hardening processing of details based on rotorscrew technological systems / V. А. Lebedev, G. V. Serga, А. V. Khandozhko // IOP Conference Series. Materials Science and Engineering. — 2018. — Vol. 327. — P. 042062. DOI: 10.1088/1757-899X/327/4/042062

7. Бабичев, А. П. Исследования основных технологических параметров формирования вибрационного ме-ханохимического покрытия и качества оксидной пленки / А. П. Бабичев, П. Д. Мотренко // Упрочняющие технологии и покрытия. — 2011. — № 5. — С. 33-38.

8. Antonova, N. M. Evaluation of adhesion strength of protective coatings with Al powder by adhesion work of initial suspension towards metal surface / N. M. Antonova // International Conference on Modern Trends in Manufacturing Technologies and Equipment (ICMTMTE 2018) : MATEC Web of Conferences. — 2018. — Vol. 224 (1). — P. 03011. — URL: https://www.matec-conferences.org/articles/matecconf/pdf/2018/83/matecconf_icmtmte2018_03011.pdf (accessed: 12.11.2020).

9. Определение адгезии путем цифровой обработки изображений поверхности покрытий / Н. М. Антонова, И. А. Зиновьев, Е. Ю. Хаустова [и др.] // Инженерный вестник Дона : [сайт]. — 2019. — № 1. — URL : ivdon.ru/ru/magazine/archive/n1y2019/5549 (дата обращения : 20.10.2020).

10. Лебедев, В. А. Повышение эффективности вибрационной отделочной обработки деталей на основе применения сред органического происхождения / В. А. Лебедев, Е. Ю. Крупеня, А. П. Шишкина // Прогрессивные машиностроительные технологии, оборудование и инструменты / Под ред. А. Н. Киричика. — Москва : Спектр, 2015. — Т. 6. — С. 268-326.

11. Lebedev, V. А. Increase of efficiency of finishing-cleaning and hardening processing of details based on rotorscrew techno-logical systems / V. А. Lebedev, G. V. Serga, А. V. Khandozhko / IOP Conference Series. Materials Science and Engineering. — 2018. — Vol. 327 (4). — P. 042062. DOI: 10.1088/1757-899X/327/4/042062

12. Зверовщиков, А. Е. Расширение технологических возможностей объемной центробежно-планетарной обработки / А. Е. Зверовщиков // Наукоемкие технологии в машиностроении. — 2013. — № 7. — С. 17-23.

13. Мартынов, А. Н. Определение скорости резания при объемной центробежно-планетарной обработке / А. Н. Мартынов, В. З. Зверовщиков, А. Е. Зверовщиков // Вестник машиностроения. — 1996. — № 9. — С. 25-27.

14. Зверовщиков, А. Е. О формировании шероховатости поверхности на труднодоступных участках профиля детали при объемной центробежной обработке гранулированными средами / В. З. Зверовщиков, А. В. Пону-калин, А. Е. Зверовщиков // Известия высших учебных заведений. Поволжский регион. Технические науки. — 2010. — № 3 (15). — С. 114-122.

15. Shtyn, S. U. Thermodynamic aspects of the coating formation through mechanochemical synthesis in vibration technology systems / S. U. Shtyn, V. A. Lebedev, A. O. Gorlenko // IOP Conference Series. Materials Science and Engineering. — 2016. — Vol. 177. — P. 012127. DOI: 10.1088/1757-899X/177/1/012127