Preview

Advanced Engineering Research (Rostov-on-Don)

Advanced search

Engineering support for specified quality of parts surface layer under dynamic methods processing of surface plastic deformation

https://doi.org/10.12737/20220

Abstract

The work objective is the optimization of the part cutting process to ensure the specified surface layer quality when using the dynamic methods of the surface plastic deformation (SPD). The research subject is the process of forming the surface layer parameters that ensure the rational SPD processing modes. The adjusted dependences for determining the hardened layer depth, the degree of hardening and roughness of the surface layer are presented. The analytical prediction technique of the parts surface layer quality parameters is developed on the basis of the abovementioned relations. These relations are experimentally tested and can be used for designing high-performance, cost-effective technological processes based on the application of the dynamic SPD methods. The importance of the process optimization based on the criterion of the workpieces durability is noted. A control-flow chart of the dynamic SPD machining optimization is given.

About the Authors

Mikhail A. Tamarkin
Don State Technical University
Russian Federation


Аlexandra S. Shvedova
Don State Technical University
Russian Federation


Roman V. Grebenkin
Don State Technical University
Russian Federation


Sergey А. Novokreshchenov
Don State Technical University
Russian Federation


References

1. Rajendran, R., Raman Nagar, C.-V. Strain hardening exponents and strength coefficients for aeroengine isotopic metallic materials — a reverse engineering approach. Gas Turbine Research Establishment, 2014, no. 2, pp. 1–2.

2. Tamarkin, M.A., Tishchenko, E.E., Lebedenko, V.G. Surface-layer quality in shot treatment. Russian Engineering Research, 2010, vol. 30, no. , pp. 144–148.

3. Shvedova, А.S. Povyshenie ekspluatatsionnykh svoystv detaley pri obrabotke dinamicheskimi metodami poverkhnostnogo plasticheskogo deformirovaniya. [Improvement of part service properties under surface plastic deformation treatment by dynamic methods.] Vestnik of DSTU, 2015, no. 1 (80), pp. 114–120 (in Russian).

4. Lebedev, V.А. Klassifikatsiya i fiziko-tekhnologicheskie aspekty dinamicheskikh metodov poverkhnostnoplasticheskogo deformirovaniya. [Classification and physico- technological aspects of dynamic methods of surface-plastic deformation.] Vestnik of DSTU, 2011, vol. 11, no. 6 (57), pp. 884–891 (in Russian).

5. Tamarkin, M.A., et al. Tekhnologicheskie osnovy optimizatsii otdelochno-uprochnyayushchey obrabotki detaley v granulirovannykh rabochikh sredakh. [Techniques of optimization of finishing and hardening part treatment in granular operating environments.] Strengthening Technologies and Coatings, 2015, no. 11, pp. 12–16 (in Russian).

6. Drozd, М.S., Matlin, M.M., Sidyakin, Y.I. Inzhenernye raschety uprugoplasticheskoy kontaktnoy deformatsii. [Engineering calculations of elastoplastic contact deformation.] Moscow: Mashinostroenie, 1986, 224 p. (in Russian).

7. Sidyakin, Y.I. Razrabotka metodov rascheta uprugoplasticheskikh kontaktnykh deformatsiy v protsessakh uprochneniya detaley poverkhnostnym plasticheskim de- formirovaniem: avtoref. dis. … dokt. tekhn. nauk. [Development of calculation methods of elastoplastic contact deformation in the processes of part hardening by superficial plastic deformation: Dr.Sci. (Eng.) diss., author’s abstract.]. Moscow, 2002, 34 p. (in Russian).

8. Kudryavtsev, I.V., et al. Povyshenie prochnosti i dolgovechnosti krupnykh detaley mashin poverkhnostnym naklepom. [Increasing strength and durability of large machine parts by surface cold working.]. Moscow: NIIINFORMTYaZhMASh, 1970, 144 p. (in Russian).

9. Tishchenko, E.E. Povyshenie effektivnosti otdelochno-uprochnyayushchey tsentrobezhno-rotatsionnoy obrabotki: dis. … kand. tekhn. nauk. [Improving efficiency of finishing-strengthening centrifugally-rotational treatment: Cand.Sci. (Eng.) diss.] Rostov-on-Don, 2004, 151 p. (in Russian).

10. Gruby, S.V. Optimizatsiya protsessa mekhanicheskoy obrabotki i upravlenie rezhimnymi parametrami. [Machining process optimization and operating parameters control.] Moscow: Bauman MSTU Publ. House, 2014, 149 p. (in Russian).

11. Tamarkin, М.А. Teoreticheskie osnovy optimizatsii protsessov obrabotki detaley svobodnymi abrazivami : dis … dokt. tekhn. nauk. [Optimization fundamentals of component processing by loose abrasives: Dr.Sci. (Eng.) diss.] Rostov-on- Don, 1995, 285 p. (in Russian).


Review

For citations:


Tamarkin M.A., Shvedova А.S., Grebenkin R.V., Novokreshchenov S.А. Engineering support for specified quality of parts surface layer under dynamic methods processing of surface plastic deformation. Vestnik of Don State Technical University. 2016;16(3):46-52. (In Russ.) https://doi.org/10.12737/20220

Views: 565


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2687-1653 (Online)