Reliability of parts and unrestorable components in the machine design
https://doi.org/10.23947/1992-5980-2018-18-4-392-400
Abstract
Introduction. The issues on standardization of reliability indices in the early stages of machine design are considered. This approach maintains thetarget level of reliability when developing parts that are critical in view of stable operation. The work objective is to study design problems in this area. The analysis of the reliability regulation methods suggests that they are insufficient to design. Besides, there are some contradictions associated with the use of the exponential failure law in design.
Materials and Methods. At the stage of the task order, the numerical values of the operation time and reliability of the machine are determined. Then the values of the reliability probabilities or failures of the system and its elements are shown by exponential expressions. In them, degrees are the ranking parameters of the system reliability indices.
Research Results. The alternative approach to normalization is synthesized; it enables to complete a full structural analysis. Thus, the reliability indices of the entire system or parts, whose operational safety determines the machine reliability, can be assessed. Parts and other components, whose failures are not sudden, are considered without using the exponential law. This preserves the inherent simplicity of mathematical operations.
Discussion and Conclusions. The numerical value of the reliability probability (RP) of the machine as a whole, taken at the stage of the task order, is insufficient for the reliability target design. The specified RP and running time of the system elements, which are sources of failures developing according to different laws, are required. The results obtained can be used both in designing new mechanical systems with the reliability target, and in the modernization of machines.
About the Authors
Yu. P. Manshin
Don State Technical University
Russian Federation
Russian Federation
Manshin, Yury P. - associate professor of the Machine Design Principles Department, Cand.Sci. (Eng.), associate professor
1, Gagarin sq., Rostov-on-Don, 344000, RF
E. Yu. Manshina
Don State Technical University
Russian Federation
Russian Federation
Manshina, Elena Yu. - senior lecturer of the Machine Design Principles Department
1, Gagarin sq., Rostov-on-Don, 344000, RF
References
1. GOST 15.001-88. Sistema razrabotki i postanovki produktsii na proizvodstvo. Produktsiya proizvodstvenno-tekhnicheskogo naznacheniya. [GOST 15.001-88. System of product development and launching into manufacture. Products of industrial and technical designation.] USSR State Standards Committee. Moscow: Izd-vo standartov, 1988,7p. (in Russian).
2. GOST 2.103-2013. Edinaya sistema konstruktorskoy dokumentatsii. Stadii razrabotki. [Unified system for design documentation. Stages of designing.] All-Russian Research Institutefor Standardization and Certification in Mechanical Engineering; Research Center of CALS-technologies “Applied Logistics”; Federal Agency for Technical Regulation and Metrology;Interstate Council for Standardization, Metrology and Certification. Moscow: Standartinform, 2015, 6p. (in Russian).
3. Manshin, Yu.P., Manshina, E.Yu. Planirovanie i otsenka nadezhnosti tekhnicheskoy sistemy na rannikh stadiyakh proekta. [Planning and assessing the technical system reliability in early stages of the project.]Sostoyanie i perspektivy razvitiya sel'skokhozyaystvennogo mashinostroeniya: sb. statey 7-y mezhdunar. nauch.-prakt. konf. v ramkakh 17-y Mezhdunar. agroprom. vystavki «Interagromash-2014» [State and prospects of agricultural machinery development: Proc. 7th Int. Sci.-Pract. Conf.within framework of the 17 th Int. Agroindustrial Exhibition “Interagromash-2014”.] Rostov-on-Don: DSTU Publ. Centre, 2014, pp. 169–171(in Russian).
4. Kovalev, A.N., Kantor, B.I., Mozhaev, A.B. Ekonomicheskoe obespechenie nadezhnosti mashin. [Economic reliability control of machines.] Moscow: Mashinostroenie, 1991, 238p. (in Russian).
5. Dalskiy, A.M. Tekhnologicheskoe obespechenie nadezhnosti vysokotochnykh detaley mashin. [Technological support for the reliability of high-precision machine parts.] Moscow: Mashinostroenie, 1975, 225p. (in Russian).
6. Volkov, D.P., Nikolaev, S.N. Nadezhnost' stroitel'nykh mashin i oborudovaniya.[Reliability of construction machines and equipment.] Moscow: Vysshaya shkola, 1979,400p.(in Russian).
7. Pronnikov, A.S. Parametricheskaya nadezhnost' mashin. [Parametric machine reliability.]Moscow: Bauman University Publ. House, 2002,560p.(in Russian).
8. Shubin, V.S., Ryumin, Yu.A. Nadezhnost' oborudovaniya khimicheskikh i neftepererabatyvayushchikh proizvodstv. [Reliability of chemical and oil refining equipment.] Moscow: Khimiya; KolosS, 2006, 359p. (in Russian).
9. Androsov, A.A., Manshin, Yu.P., Manshina, E.Yu. Kursovoe proektirovanie tekhnicheskikh sistem s zadannym urovnem nadezhnosti. [Course design of engineering systems with the specifiedreliability level.] Rostov-onDon: DSTU Publ. Centre, 2013, 93p. (in Russian).
10. Polovko, A.M., Gurov, S.V. Osnovy teorii nadezhnosti. [Fundamentals of the reliability theory.] St.Petersburg: BKhV-Peterburg, 2006,704p. (in Russian).
11. Druzhinin, G.V.Nadezhnost' avtomatizirovannykh system. [Reliability of automated systems.] 3 rd revised and enlarged ed. Moscow: Energiya, 1977, 536p.(in Russian).
12. Manshin, Yu.P., Manshina, E.Yu. Raschety parametrov nadezhnostielementov pri proektirovanii mashin. [Calculations of the reliability parameters of elements under machine design.] Sostoyanie i perspektivy razvitiya sel'skokhozyaystvennogo mashinostroeniya: mat-ly 7-y mezhdunar. nauch.-prakt. konf. v ramkakh 20-ymezhdunar. agroprom. vystavki «Interagromash-2017».[State and prospects of agricultural machinery development: Proc. 7th Int. Sci.-Pract. Conf.within framework of the 20 th Int. Agroindustrial Exhibition “Interagromash-2017”.] Rostov-on-Don: DSTU Publ. Centre, 2017, pp.261–263(in Russian).
13. Gnedenko, B.V., Belyaev, Yu.K., Solovyev, A.D. Matematicheskie metody v teorii nadezhnosti.[Mathematical methods in the theory of reliability.] Moscow: Nauka, 1965, 573p. (in Russian).
14. Khozyaev, I.A. Nadezhnost' biotekhnicheskikh sistem. [Reliability of biotechnical systems.] Rostov-on-Don: DSTU Publ. Centre, 2014, 235p.(in Russian).
15. Manshin, Yu.P., Manshina, E.Yu. Priblizhennaya otsenka resursa detali, obespechivayushchaya ee trebuemyy resurs s zadannoy veroyatnost'yu bezotkaznoy raboty.[Aproximate assession of part life, assuring its required life with specified probability of no-failure operation.] Vestnik Mashinostroeniya, 2017, no. 12, pp.20–24(in Russian).
16. Man’shin, Yu.P., Man’shina, E. Yu. Estimating the Life of a Machine Part. Russian Engineering Research, 2018, vol.38, no.3, pp. 157–162.
Review
For citations:
Manshin Yu.P., Manshina E.Yu. Reliability of parts and unrestorable components in the machine design. Vestnik of Don State Technical University. 2018;18(4):392-400. https://doi.org/10.23947/1992-5980-2018-18-4-392-400
Views:
678
Email this article 