Preview

Advanced Engineering Research (Rostov-on-Don)

Advanced search

Error effect of executive elements movement of the lathe tool on forming motion paths

https://doi.org/10.23947/1992-5980-2017-17-1-35-46

Abstract

Introduction. Any metal-cutting machine has errors of the executive elements movement depending on its geometric accuracy and state. These errors change the forming motions indirectly, through their transformation by the dynamic cutting system with account for the elastic deformations of the tool and the workpiece. Materials and Methods. Laws of the relation between the executive elements and forming paths for the longitudinal cutting case are considered. All deformation displacements are counted off from the independent coordinate system anchored to the carrier system of the machine which is considered to be absolutely rigid and non-deforming. Research Results. A mathematical transformation model consisting of two elastic-deformation subsystems on the part of the tool and workpiece that interact through the dynamic link generated by the cutting process is proposed. This model allows for the errors of the executive elements movement. They are specified by the kinematic disturbances and spindle wavering, and a workpiece in the space. Discussion and Conclusions. Therefore, as opposed to the known studies, it is shown how the mathematical formulation and parameters of the dynamic link generated under the cutting process are changed depending on the kinematic and other types of disturbances. Two types of disturbances are fully considered: those inducing speed variations of the tool motion relative to the workpiece in the direction to the caliper mobility, and disturbances in the form of oscillating displacements in the orthogonal direction to the feed velocity attitude. These disturbances are generated as radial and axial spindle wavering, and as speed variations of the longitudinal feed and variations of the caliper position relative to the ideal rotation axis of the part. It is shown, that the law of the disturbance transformation into the forming movements trajectories depends on the frequency content of the disturbances. The examples are provided, and the conclusions about the transformation properties are made. In particular, it is shown that the speed variations in the direction to the longitudinal feed with the frequency equal to or multiple of the spindle rotation frequency in no way image into the forming movement trajectories.

About the Authors

Vilor L. Zakovorotny
Don State Technical University
Russian Federation


Valery E. Gvindzhiliya
Don State Technical University
Russian Federation


References

1. Reshetov, D.N., Portman, V.T. Tochnost' metallorezhushchikh stankov. [Accuracy of cutting machines.] Moscow: Mashinostroenie, 1986, 336 p. (in Russian).

2. Kadyrov, R.R., Kudoyarov, R.G. Opredelenie sostava osnovnykh proverok geometricheskoy tochnosti metallorezhushchego stanka. [Determination of configuration of the basic checks of geometrical accuracy of metal cutting machine.] STIN, 2016, no. 8, pp. 2–7(in Russian).

3. Zakovorotny, V. L., Lukyanov, A.D. The Problems of Control of the Evolution of the Dynamic System Interacting with the Medium. International Journal of Mechanical Engineering and Automation, 2014, vol. 1, no. 5, pp. 271–285.

4. Zakovorotny, V. L., Lukyanov, A.D. System synthesis of Machine tool manufacturing process control based on synergetic conception. Procedia Engineering, 2016, vol. 150, pp. 370–375.

5. Zakovorotny, V.L., Flek, M.F., Pham Dinh Tung. Sinergeticheskaya kontseptsiya pri postroenii sistem upravleniya tochnost'yu izgotovleniya detaley slozhnoy geometricheskoy formy. [Synergetic concept in construction of accuracy control systems for manufacturing parts of complex geometric forms.] Vestnik of DSTU, 2011, vol. 11, no. 10 (61), pp. 1785–1797 (in Russian).

6. Zakovorotny, V.L., Panov, E.Y., Potapenko, P.N. Svoystva formoobrazuyushchikh dvizheniy pri sverlenii glubokikh otverstiy malogo diametra. [Properties of forming movements when drilling deep pinholes.] Vestnik of DSTU, 2001, vol. 1, no. 2, pp. 81–93 (in Russian).

7. Zakovorotny, V.L., Lapshin, V.P., Turkin, I.A. Upravlenie protsessom sverleniya glubokikh otverstiy spiral'nymi sverlami na osnove sinergeticheskogo podkhoda. [Process control drilling deep holes twist drills based on the synergetic approach.] University News. North-Caucasian region. Technical Sciences Series, 2014, no. 3 (178), pp. 33–41 (in Russian).

8. Zakovorotny, V.L., Sankar, T., Borodachev, E.V. Sistema optimal'nogo upravleniya protsessom glubokogo sverleniya otverstiy malogo diametra. [The optimal control system of deep drilling of pinholes.] STIN, 1994, no. 12, pp. 22 (in Russian).

9. Tlusty, I. Avtokolebaniya v metallorezhushchikh stankakh. [Self-excitation vibrations in cutting machines.] Moscow: Mashgiz, 1956, 395 p. (in Russian).

10. Tobias, S.-A. Machine Tool Vibrations. London: Blackie, 1965, 350 р.

11. Kudinov, V.A. Dinamika stankov. [Machine dynamics.] Moscow: Mashinostroenie, 1967, 359 p. (in Russian).

12. Zakovorotny, V. L. Bifurcations in the dynamic system of the mechanic processing in metal-cutting tools. WSEAS. Journal of Transactions on Applied and Theoretical Mechanics, 2015, vol. 10, pp. 102–116.

13. Zakovorotny, V.L., Pham D.-T., Bykador, V.S. Vliyanie izgibnykh deformatsiy instrumenta na samoorganizatsiyu i bifurkatsii dinamicheskoy sistemy rezaniya metallov. [Influence of a flexural deformation of a tool on self-organization and bifurcations of dynamical metal cutting system.] Izvestia VUZ. Applied Nonlinear Dynamics, 2014, vol. 22, no. 3, pp. 40–52 (in Russian).

14. Zakovorotny, V.L., et al. Bifurcation of stationary manifolds formed in the neighborhood of cutting. Journal of Sound and Vibration, 2016, vol. 368, pp. 174–190.

15. Zakovorotny, V.L., Gubanova, A.A., Lukyanov, A.D. Ispol'zovanie sinergeticheskoy kontseptsii dlya izucheniya ustoychivosti formoobrazuyushchikh traektoriy poputnogo frezerovaniya. [Use of synergetic concept for studying stability of forming trajectories of climb cutting.] STIN, 2016, no. 4, pp. 32–40 (in Russian).

16. Zakovorotny, V.L., Gubanova, A.A., Lukyanov, A.D. Usloviya parametricheskogo samovozbuzhdeniya dinamicheskoy sistemy frezerovaniya kontsevymi frezami. [Conditions for parametric self-excitation of dynamic end milling system.] STIN, 2016, no. 6, pp. 10–16 (in Russian).

17. Zakovorotny, V.L., Gubanova, A.A., Lukyanov, A.D. Prityagivayushchie mnozhestva pri frezerovanii kontsevymi frezami. [Attracting sets under end milling.] STIN, 2016, no. 8, pp. 27–33 (in Russian).

18. Zakovorotny, V.L., Pham D.T. Parametricheskoe samovozbuzhdenie dinamicheskoy sistemy rezaniya. [Parametric self-excitation of cutting dynamic system.] Vestnik of DSTU, 2013, vol. 13, no. 5/6 (74), pp. 97–103 (in Russian).

19. Zakovorotny, V. L., et al. Modelirovanie dinamicheskoy svyazi, formiruemoy protsessom tocheniya, v zadachakh dinamiki protsessa rezaniya (skorostnaya svyaz'). [Dynamic coupling modeling formed by turning in cutting dynamics problems (velocity coupling).] Vestnik of DSTU, 2011, vol. 1, no. 2 (53), pp. 137–146 (in Russian).

20. Zakovorotny, V. L., et al. Modelirovanie dinamicheskoy svyazi, formiruemoy protsessom tocheniya (pozitsionnaya svyaz'). [Dynamic coupling modeling formed by turning in cutting dynamics problems (positional coupling).] Vestnik of DSTU, 2011, vol. 11, no. 3 (54), pp. 301–311 (in Russian).

21. Haken, H. Tayny prirody. Sinergetika: uchenie o vzaimodeystvii. [Nature’s secrets. Synergetics: interaction theory.] Moscow; Izhevsk: Institute of Computer Science, 2003, 320 p. (in Russian).

22. Kolesnikov, A.A., ed. Sinergetika i problemy teorii upravleniya. [Synergetics and control theory problems.] Moscow: Fizmatlit, 2004, 504 p. (in Russian).

23. Push, A.V. Shpindel'nye uzly. Kachestvo i nadezhnost'. [Spindle blocks. Quality and reliability.] Moscow: Mashinostroenie, 1992, 288 p. (in Russian).

24. Zakovorotny, V.L., Shapovalov, V.V. Dinamika transportnykh tribosistem. [Dynamics of transportation tribosystems.] Assembling in Mechanical Engineering and Instrument-Making, 2005, no. 12, pp. 19–29 (in Russian).

25. Zakovorotny, V.L., Blokhin, V.P., Alekseychik, M.I. Vvedenie v dinamiku tribosistem. [Introduction to tribosystem dynamics.] Rostov-on-Don: InfoServis, 2004, 680 p. (in Russian).

26. Akhmanov, S.A., Dyakov, Y.E., Chirkin, A.S. Vvedenie v statisticheskuyu radiofiziku i optiku. [Introduction to statistical Radiophysics and optics.] Moscow: Nauka, 1981, pp. 124–128 (in Russian).

27. Anh, N.-D., et al. A dual criterion of stochastic linearization method for Multi-degree of freedom systems subjected to random excitation. Acta Mechanica, 2012, vol. 223, no. 12, pp. 2667–2684.

28. Anh, N.-D., Zakovorotny, V.L., Hao, D.-N. Response analysis of Van Der Pol oscillator subjected to harmonic and random excitations. Probabilistic Engineering Mechanics, 2014, vol. 37, pp. 51–59.

29. Merkin, D.R. Vvedenie v teoriyu ustoychivosti dvizheniya. [Introduction to theory of motion stability.] Moscow: Nauka, 1971, 312 p. (in Russian).

30. Lakhadanov, V.M. O vliyanii struktury sil na ustoychivost' dvizheniya. [On effect of structure of forces on motion stability.] Journal of Applied Mathematics and Mechanics, 1974, vol. 38, pp. 246–253 (in Russian).

31. Zakovorotny, V.L., Bordachev, E.V. Informatsionnoe obespechenie sistemy dinamicheskoy diagnostiki iznosa rezhushchego instrumenta na primere tokarnoy obrabotki. [Information support of the dynamic diagnostic system for cutting tool wear by the example of lathing.] Journal of Machinery Manufacture and reliability, 1995, no. 3, pp. 95–103 (in Russian).

32. Zakovorotny, V.L., Ladnik, I.V. Postroenie informatsionnoy modeli dinamicheskoy sistemy metallorezhushchego stanka dlya diagnostiki protsessa obrabotki. [Building of data model of the machine tool dynamic system for treatment process diagnostics.] Journal of Machinery Manufacture and reliability, 1991, no. 4, pp. 75–81 (in Russian).


Review

For citations:


Zakovorotny V.L., Gvindzhiliya V.E. Error effect of executive elements movement of the lathe tool on forming motion paths. Vestnik of Don State Technical University. 2017;17(1):35-46. (In Russ.) https://doi.org/10.23947/1992-5980-2017-17-1-35-46

Views: 590


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2687-1653 (Online)