Preview

Advanced Engineering Research (Rostov-on-Don)

Advanced search

TEMPERATURE EVALUATION UNDER CURVED-EDGE TOOL CUTTING

https://doi.org/10.12737/5709

Abstract

A theoretical model for determining temperature on the working surfaces of the tool with the blade shaped profile is considered. Analytical dependences for estimating the thermal state of the blade front face (tooth cutter) with an elliptical profile in normal sections are obtained. The resulting equations include the effect of thermophysical constants of the tool material and workpiece, heat transfer conditions, deformation characteristics of the cut layer, cutting modes, and tool geometry (under turning and milling)on temperature. The obtained numerical results for the temperature of the HM tool (T15K6) and HSS tool (R6M5) match the test data; they can be applied to predict the wear rate and service durability of shaped tools including blades, side and hob cutters.

About the Authors

Anatoly Andreyevich Ryzhkin
Don State Technical University, Russia
Russian Federation


Denis Vitalyevich Moiseyev
Don State Technical University, Russia
Russian Federation


References

1. Рыжкин, А. А. Обработка материалов резанием: физические основы / А. А. Рыжкин. — Ростов-на-Дону : Изд. центр Дон. гос. техн. ун-та, 1995. — 242 с.

2. Висторопская, Ф. А. К вопросу о коэффициенте распределения теплового потока в зоне деформации при резании / Ф. А. Висторопская, А. А. Рыжкин, С. А. Моисеенко // Вестн. Дон. гос. техн. ун-та. — 2012. — № 6 (67). — С. 41–46.

3. Расчёт температуры задней поверхности режущего инструмента / А. А. Рыжкин [и др.] // Проблемы синергетики в трибологии, трибоэлектрохимии, материаловедении и мехатронике : сб. тр. XI Междунар. науч.-практ. конф. — Южнорос. гос. техн. ун-т. — Новочеркасск, 2012. — С. 4–21.

4. Зубчатая передача : патент 2057267 Рос. Федерация : F16H1/24 / Г. П. Гребенюк. — За-явл. 07.04.93 ; опубл. 27.03.96, Бюл. № 9. — 5 с.

5. Определение координат боковых сторон зубьев колёс с эллиптическим профилем / А. А. Рыжкин [и др.] // Вестн. Дон. гос. техн. ун-та. — 2009. — Т. 9, № 2 (41). — С. 284–295.

6. Рыжкин, А. А. К вопросу аналитической оценки профиля эллиптического зуба колеса / А. А. Рыжкин, Д. В. Моисеев // Вестн. Дон. гос. техн. ун-та. — 2009. — Т. 9, № 4 (43). — С. 698–710.

7. Определение профиля червячной фрезы для изготовления зубчатых колёс эллиптического профиля / А. А. Рыжкин [и др.] // Вестн. Дон. гос. техн. ун-та. — 2010. — Т. 10, № 5 (48). — C. 731–743.

8. Ящерицын, П. И. Теория резания / П. И. Ящерицын, Е. Э. Фельдштейн, М. А. Корниевич. — Минск : Новое знание, 2006. — 512 с.


Review

For citations:


Ryzhkin A.A., Moiseyev D.V. TEMPERATURE EVALUATION UNDER CURVED-EDGE TOOL CUTTING. Vestnik of Don State Technical University. 2014;14(3):29-36. (In Russ.) https://doi.org/10.12737/5709

Views: 481


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2687-1653 (Online)