Reliability process methodology of the centrifugal rotary machining in the medium of steel balls
https://doi.org/10.12737/11607
Abstract
The research results on improving reliability of the finishing-strengthening centrifugal rotary processing are presented. The research subject is the formation of the finishing and strengthening centrifugal rotary processing (FS CRP) reliability provided by a reasonable coupling of the technological modes and operating environment characteristics. The research objective is to improve efficiency and reliability of the finishing-hardening centrifugal rotary processing with studying the arising failures based on the development of a set of the adequate theoretical processing patterns. The refined theoretical patterns of the finished part surface layer indices forming - the extent and depth of hardening, are obtained. The analytical forecasting methodology of the finishing-hardening centrifugal rotary processing reliability with the following parameters: the coefficient of the instantaneous scattering of the controlled variable, the offset coefficient of the controlled variable, and the coefficient of the process marginal accuracy, is developed. It is established that the FS CRP process provides obtaining the required parameters of the workpiece surface quality under the processing within the tolerance values in a certain range of the technological mode change and the operating environment characteristics. The design technique for the FS CRP processes with allowance for their reliability is developed.
About the Author
Denis Vladimirovich Kazakov
Don State Technical University, Rostov-on-Don, Russian Federation
Russian Federation
Russian Federation
References
1. Rajendran, R., Raman Nagar, C. V. Strain hardening exponents and strength coefficients for aeroengine isotopic metallic materials — a reverse engineering approach. Gas Turbine Research Establishment, 2014, pp. 1–2.
2. Tamarkin, М. А. Teoreticheskie osnovy optimizatsii protsessov obrabotki detaley svobodnymi abrazivami: dis… dra tekhn. nauk. [Theoretical foundations of optimization of loose-abrasive part machining: Dr.Sci. (Eng.) diss.] Rostov-on- Don, 1995, 179 p. (in Russian).
3. Trilisskiy, V. О., Burstein, I. E., Alferov, V. I. Ob''emnaya tsentrobezhno-rotatsionnaya obrabotka detaley. [Threedimensional centrifugal rotary part machining.] Moscow: NIImash, 1983, 53 p. (in Russian).
4. Dubrovskiy, P. V. Obespechenie nadezhnosti tekhnologicheskikh protsessov. [Reliability control of processes.] Ulyanovsk: UlGTU, 2000, 124 p. (in Russian).
5. Tishchenko, E. E. Povyshenie effektivnosti otdelochno-uprochnyayushchey tsentrobezhno-rotatsionnoy obrabotki: dis. ... kand. tekhn. nauk. [Improving the efficiency of finishing and strengthening centrifugal rotary processing: Cand.Sci. (Eng.) diss.] Rostov-on-Don, 2004, 152 p. (in Russian).
6. Korolkov, Y. V. Povyshenie nadezhnosti tekhnologicheskogo protsessa tsentrobezhno-rotatsionnoy obrabotki v srede abraziva: dis. … kand. tekhn. nauk. [Increase of reliability control of centrifugal rotary treatment in abrasive medium: Cand.Sci. (Eng.) diss.] Rostov-on-Don, 2011, 186 p. (in Russian).
7. Druppov, V. V. Optimizatsiya protsessa tsentrobezhno-rotatsionnoy obrabotki v srede abraziva: dis. ... kand. tekhn. nauk. [Optimization of centrifugal rotary machining in abrasive medium: Cand.Sci. (Eng.) diss.] Rostov-on-Don, 2007, 170 p. (in Russian).
8. Suslov, А. G., Dalskiy, A. M. Nauchnye osnovy tekhnologii mashinostroeniya. [Scientific basis of mechanicalengineering technology.] Rostov-on-Don, 2002. — 684 с. (in Russian).
9. Korolkov, Y. V. Обеспечение надежности технологических процессов центробежно-ротационной обработки свободным абразивом [Reliability control of production processes of centrifugal rotary treatment by loose abrasive.] Vestnik of DSTU, 2011, vol. 11, iss. 1, no. 8 (59), pp. 1249–1251 (in Russian).
10. Rozhnenko, О. А., Tishchenko, E. E., Tamarkina, E. M., Korolkov, Y. V. Modelirovanie protsessov obrabotki fasonnykh poverkhnostey detaley svobodnym abrazivom. [Modeling of loose-abrasive machining technique for profiled surfaces.] Vestnik of DSTU, 2011, vol. 11, no. 5(56), pp. 701–704 (in Russian).
Review
For citations:
Kazakov D.V. Reliability process methodology of the centrifugal rotary machining in the medium of steel balls. Vestnik of Don State Technical University. 2015;15(2):48-55. (In Russ.) https://doi.org/10.12737/11607
Views:
557
Email this article 