SERVOMOTOR PARAMETER EFFECT ON DYNAMIC PROPERTIES OF TWIST DRILLING DEEPHOLE MACHINING SYSTEM
Abstract
The property change of the unified dynamic system is considered by the example of the deephole machining process. It is shown that due to the nonlinear relationship formed by the cutting process, in the system, as a rule, the only balance point with the bounded domain of attraction is constructed. The given materials on investigating the domain of attraction show that it depends on the control and cutting forces presented in the state coordinates of the interacting subsystems. While shaving is being accumulated in the chip clearance grooves, this domain degenerates, and the system becomes totally unstable. At this, the tool is blocked, and as a rule, broken. It is shown that the domain of attraction and evolutionary changes of the system properties depending on the shaving accumulation in the drill flutes are basically related to the interacting servomotors parameters. It is proposed to adjust the servomotor parameters on the basis of the introduction of special links.
About the Authors
Vilor Lavrentyevich ZakovorotnyRussian Federation
Ilya Andreyevich Turkin
Russian Federation
Victor Petrovich Lapshin
Russian Federation
References
1. Заковоротный, В. Л. Математическое моделирование и параметрическая идентификация динамических свойств подсистем инструмента и заготовки при точении / В. Л. Заковоротный, Фам Динь Тунг, Нгуен Суан Тьем // Известия высших учебных заведений. Северо-Кавказский регион. Технические науки. — 2011. — № 2. — С. 38‒46.
2. Заковоротный, В. Л. Динамика процесса резания. Синергетический подход / В. Л. Зако-воротный, М. Б. Флек. — Ростов-на-Дону : Терра, 2006. — 876 с.
3. Кудинов, В. А. Динамика станков / В. А. Кудинов. — Москва : Машиностроение, 1967. — 357 с.
4. Заковоротный, В. Л. Динамический мониторинг состояния процесса резания / В. Л. Зако-воротный, Е. В. Бордачёв, М. И. Алексейчик // Станки и инструменты. — 1998. — № 12. — С. 6‒12.
5. Заковоротный, В. Л. Построение информационной модели динамической системы ме-таллорежущего станка для диагностики процесса обработки / В. Л. Заковоротный, И. В. Ладник // Проблемы машиностроения и надёжности машин. — 1991. — № 4. — С. 75.
6. Заковоротный, В. Л. Параметрические явления при управлении процессами обработки на станках / В. Л. Заковоротный, Фам Динь Тунг, Фам Тху Хыонг // Вестник Дон. гос. техн. ун та. — 2012. — № 7 (68). — С. 52‒61.
7. Заковоротный, В. Л. Влияние скоростных связей на устойчивость равновесия динамиче-ской системы резания / В. Л. Заковоротный, Фам Динь Тунг, Нгуен Суан Тьем // Вестник Дон. гос. техн. ун-та. — 2011. — Т. 11, № 8 (59), вып. 1. — С. 1169‒1179.
8. А dual criterion of stochastic linearization method for multi-degree-of-freedom systems sub-jected to random excitation / N. D. Anh [et al.] // Acta Mechanica. — 2012. — Vol. 223, № 12. — Pp. 2667‒2684.
9. Лапшин, В. П. Влияние свойств серводвигателя шпинделя на динамику сверления глубоких отверстий малого диаметра / В. П. Лапшин, И. А. Туркин // Вестник Дон. гос. техн. ун-та. — 2013. — № 5/6 (74). — C. 125‒130.
10. Грановский, Г. И. Резание металлов / Г. И. Грановский. — Москва : Высш. школа, 1985. — 304 с.
Review
For citations:
Zakovorotny V.L., Turkin I.A., Lapshin V.P. SERVOMOTOR PARAMETER EFFECT ON DYNAMIC PROPERTIES OF TWIST DRILLING DEEPHOLE MACHINING SYSTEM. Vestnik of Don State Technical University. 2014;14(2):56-65. (In Russ.) https://doi.org/10.12737/4485