PRINCIPLES OF CONCEPTUAL APPROACH TO CREATING TOOL SUBSYSTEM FOR MULTIOPERATION MACHINE SMART-PASSPORT
https://doi.org/10.23947/1992-5980-2014-2-74-83
Abstract
The basic principles of the construction and operation of the machine monitoring system in the computer-integrated manufacturing are described. The tool condition and the tooling backup control are the focus of attention. The proposed approach is aimed at creating conditions for the effective functioning, and the tool state management using a knowledge system of TOOL unit of the machine Smart-passport. The unit architecture is presented by a set of modules including a data acquisition module, a module for observing changes in the tool state and control, a monitoring module, and others. The significant innovation of the research is the introduction of the concepts of fuzzy boundary and border lines of sizing wear, and of overall tool life based on the theory of fuzzy knowledge concepts. The introduction of these concepts is related to the necessity to adapt modes of cutting and decision making depending on the tool state and its effect on the part accuracy.
About the Authors
Andrey Kirillovich TugengoldRussian Federation
Andrey Igorevich Izyumov
Russian Federation
References
1. Тугенгольд, А. К. Интеллектуальные функции и управление автономными технологически-ми мехатронными объектами / А. К. Тугенгольд, Е. А. Лукьянов. — Ростов-на-Дону: Изд. центр ДГТУ, 2013. — 203 с.
2. Тугенгольд, А. К. Smart-Passport открытой мехатронной технологической системы. Контент / А. К. Тугенгольд // Интеллектуальная электронная документация. — Saarbrucken : Lambert Academic Publishing, 2013. — 83 c.
3. Принципы построения интеллектуальной электронной документации станка / Г. В. Самоду-ров [и др.] // Станки, инструмент. — 2012. — № 7. — С. 15‒20.
4. Тугенгольд, А. К. Smart-паспорт мехатронного технологического объекта. Концепт / А. К. Тугенгольд, А. А. Бердичевский // Вестник Дон. гос. техн. ун-та. — 2012. — № 7. — С. 33‒41.
5. Палей, С. М. Некоторые особенности эксплуатации токарных станков с ЧПУ на участке АСВ-20 / С. М. Палей // Автоматизированные участки из станков с ЧПУ, управляемые ЭВМ: сб. ст. — Москва : ЭНИМС, 1998. — С. 27‒31.
6. Григорьев, С. Н. Повышение производительности фрезерования с помощью диагностиро-вания состояния инструмента с учётом достоверности отображения состояния объекта по критерию его отказа / С. Н. Григорьев, В. Д. Гурин, Н. Ю. Черкасова // Вестник Моск. гос. техн. ун-та «СТАН-КИН». — 2011. — № 3 (15). — С. 44‒48.
7. Кочеровский, Е. В. Диагностика состояния инструмента по силовым характеристикам про-цесса резания. Обзор / Е. В. Кочеровский, Г. М. Лихцер. — Москва : ВНИИТЭМР, 1988. — Вып. 7. — 40 с.
8. Sensor Fused Intelligent Monitoring System for Machining (SIMON) project from Intelligent Man-ufacturing Systems (IMS). Final Report [Электронный ресурс] / J. Hernendez [et al.] ; European IMS-SIMON consortium. — Режим доступа: http://www.ims.org/wp-content/uploads/2012/11/2.4.32.2-Final-Report-SIMON.pdf (дата обращения: 03.03.2014).
9. Тугенгольд, А. К. Моделирование базы знаний системы управления мехатронным объектом / А. К. Тугенгольд, А. А. Кузьмин // Известия высших учебных заведений. Северо-Кавказский регион. Технические науки. Специальный выпуск «Мехатроника. Современное состояние и тенденции разви-тия». — 2009. — С. 69‒73.
10. Макаров, А. Д. Износ и стойкость режущих инструментов / А. Д. Макаров. — Москва : Машиностроение, 1976. — 278 с.
11. Синопальников, В. А. Надёжность и диагностика технологических систем: учебник / В. А. Синопальников, С. Н. Григорьев. — Москва : Высшая школа, 2005. — 343 с.
12. Vallejo, A.-J. On-line Cutting Tool Condition Monitoring in Machining Processes using Artificial Intelligence / A.-J. Vallejo, R. Morales-Menéndez, J.-R. Alique // Robotics, Automation and Control / edited by Pavla Pecherková, Miroslav Flídr, Jindřich Duník. — Vienna : I-Tech, 2008. — 494 p.
13. Bagci, E. Monitoring and analysis of MRR-based feedrate optimization approach and effects of cutting conditions using acoustic sound pressure level in free-form surface milling / E. Bagci // Scientific Research and Essays. — 2011. — Vol. 6 (2). — Pp. 256‒277.
14. Высокопроизводительная обработка металлов резанием / AB Sandvik Coromant, ОАО «Сандвик-МКТС». — Москва : Полиграфия, 2003. — 301 с.
Review
For citations:
Tugengold A.K., Izyumov A.I. PRINCIPLES OF CONCEPTUAL APPROACH TO CREATING TOOL SUBSYSTEM FOR MULTIOPERATION MACHINE SMART-PASSPORT. Vestnik of Don State Technical University. 2014;14(2):74-83. (In Russ.) https://doi.org/10.23947/1992-5980-2014-2-74-83